基于ANSYS/LS-DYNA的电磁冲击系统阀芯动力学研究

本文以电磁冲击系统为研究对象,利用ANSYS/LS-DYNA非线性分析软件对电磁冲击系统的阀芯冲击过程进行了模拟仿真,并对阀芯运动以及阀芯回程冲击盖板进行了应力、能量传递过程的计算分析。仿真结果表明,加入缓冲弹簧后,不但提高了阀芯的使用寿命,而且阀芯能量传递效率也提高了。     

基于LabVIEW的通信系统的构建

本设计基于LabVIEW仿真软件完成了基本通信系统和通信综合系统的构建。该系统涵盖了模拟调制,数字调制,模拟信号数字传输,信道编码,最佳接收系统几部分内容。通过系统仿真,实现了系统输入输出波形的直观显示,解决了教学中实验效果不理想,理论内容不好理解的问题。同时通过内置的Web Server进行网页发布后,用户可以在客户端通过web浏览器远程调用并运行本系统,提高效率,节约成本。     

Multifractal Spectrum and Calculation

多重分形理论是进行信号奇异性处理的有用工具 ,由于只有少数集合的多重分形谱可以有解析表达式 ,多重分形谱的计算是其中重要而又较难处理的问题 .简要介绍了多重分形理论的一种形式体系 ,提出了一种采用动态链表来进行多重分形谱计算的方法 ,大幅度地降低了对存储器容量的要求 .用所提出的方法对康托集进行了计算 ,计算结果与理论结果相符 ,表明了算法的有效性 .     

翼型边界层及近场尾流的湍流特性与气动噪声特性相关规律试验研究

变湍流度试验结果表明 ,湍流度对翼型边界层和尾流的湍流特性、转捩情况、气动噪声特性及其它们间的相关特性有显著影响。这种影响有一定规律。笔者得出了苦干有价值的半经验关系式。     

Global aerodynamic design optimization based on data dimensionality reduction

In aerodynamic optimization, global optimization methods such as genetic algorithms are preferred in many cases because of their advantage on reaching global optimum. However, for complex problems in which large number of design variables are needed, the computational cost becomes prohibitive, and thus original global optimization strategies are required. To address this need, data dimensionality reduction method is combined with global optimization methods, thus forming a new global optimization system, aiming to improve the efficiency of conventional global optimization. The new optimization system involves applying Proper Orthogonal Decomposition (POD) in dimensionality reduction of design space while maintaining the generality of original design space. Besides, an acceleration approach for samples calculation in surrogate modeling is applied to reduce the computational time while providing sufficient accuracy. The optimizations of a transonic airfoil RAE2822 and the transonic wing ONERA M6 are performed to demonstrate the effectiveness of the proposed new optimization system. In both cases, we manage to reduce the number of design variables from 20 to 10 and from 42 to 20 respectively. The new design optimization system converges faster and it takes 1/3 of the total time of traditional optimization to converge to a better design, thus significantly reducing the overall optimization time and improving the efficiency of conventional global design optimization method.     

大型水陆两栖飞机侧风起降的滑流影响分析

大型水陆两栖飞机AG600的动力装置为安装在机翼上的4台同向旋转涡轮螺旋桨发动机，针对1：15缩比模型带动力风洞试验显示的螺旋桨滑流对侧风起降状态的偏航力矩不稳定影响，对全机带动力风洞试验模型进行了大规模并行非定常数值计算，再现了风洞试验现象，通过流动机理分析明确其产生原因主要是左侧滑时右外翼分离和垂尾背鳍涡破裂，这些原因和数值模拟的准确性也为后期的风洞试验所证实。考虑到模型风洞试验中尺度限制造成的低雷诺数和高螺旋桨转速，为保证飞行安全，继续采用该非定常方法对全尺寸飞机真实侧风起降状态进行了详细数值分析和偏航稳定性评估。研究结果显示，在飞行雷诺数和螺旋桨转速下，相同侧风范围内风洞试验显示的流动不稳定因素基本消失，偏航稳定性允许的侧风范围明显增加。本研究实现了四发螺旋桨飞机起降状态横向气动特性的滑流影响非定常数值分析，建立了基于计算流体力学的风洞与飞行雷诺数效应的相互关系，进行了偏航稳定性的虚拟试飞评估，研究成果也为AG600飞机的首飞和飞行试验所验证。     

激光功率与底面状态对选区激光熔化球化的影响

为研究激光功率与底面状态对选区激光熔化熔池流动的影响，基于离散单元法建立了选区激光熔化铺粉模型，采用粒径分布与实验相符的马氏体时效钢粉末分别铺展到平坦底面和增材底面上，将计算获得的粉末分布导入到基于有限体积法建立的选区激光熔化熔池计算流体力学模型中，研究激光功率和基板底面粗糙度对熔池流动和熔道表面形貌的影响。采用激光单道扫描实验验证铺粉模型和选区激光熔化模型。结果表明：随着激光功率的降低，单位长度的球化数量增加；由于增材底面使熔池润湿性变差，同时又对熔池流动行为产生扰动，使得增材粗糙底面上熔道的球化数量增加。选区激光熔化铺粉模拟及激光单道扫描模拟结果与实验结果吻合较好。本研究可为选区激光熔化工艺中工艺参数的选择提供理论指导。     

一种语音信号欠定盲分离的新方法

文章提出了一种语音信号欠定盲分离的新方法,引入了一种伪提取矢量的概念,并通过在信号采样点处选取对应的伪提取矢量,以恢复取值占优的源信号采样点的值,来实现欠定盲源分离。通过将该方法与传统的基于线性规划的欠定盲源分离方法分别仿真表明:文章所提出方法由于在信号的各采样点处无需优化,因此大大提高了信号分离的速度,语音信号的分离速度比基于线性规划的方法快数倍。     

Experimental investigation and correlation development of jet impingement heat transfer with two rows of aligned jet holes on an internal surface of a wing leading edge

Extensive experimental studies on the heat transfer characteristics of two rows of aligned jet holes impinging on a concave surface in a wing leading edge were conducted, where50000 Rej 90000, 1.74 H/d 27.5, 66° a 90°, and 13.2 r/d 42.03. The finding was that the heat transfer performance at the jet-impingement stagnation point with two rows of aligned jet holes was the same as that with a single row of jet holes or the middle row of three-row configurations when the circumferential angle of the two jet holes was larger than 30°. The attenuation coefficient distribution of the jet impingement heat transfer in the chordwise direction was so complicated that two zones were divided for a better analysis. It indicated that: the attenuation coefficient curve in the jet impingement zone exhibited an approximate upside-down bell shape with double peaks and a single valley; the attenuation coefficient curve in the non-jet impingement zone was like a half-bell shape, which was similar to that with three rows of aligned jet holes; the factors,including Rej, H/d and r/d, affected the attenuation coefficient value at the valley significantly.When r/d was increased from 30.75 to 42.03, the attenuation rates of attenuation coefficient increased only by 1.8%. Consequently, experimental data-based correlation equations of the Nusselt number for the heat transfer at the jet-impingement stagnation point and the distributionof the attenuation coefficient in the chordwise direction were acquired, which play an important role in designing the wing leading edge anti-icing system with two rows of aligned jet holes.     

基于莫尔条纹测量法设计的船体变形测量系统

介绍了一种基于莫尔条纹测量法设计的船体变形测量系统,分析了测量精度,并通过模拟实验证明了其可行性。